UPVC Replacement Door Handles
The handles on your doors get worn out over time and need to be replaced. When doing this it is crucial that the new handles conform to the dimensions of the previous handle.
The three measurements to be inspected are the top screw position as well as the key hole and lever dimensions. Use the size guide to aid you.
Inline Lever/Lever
A lever door handle is a contemporary handle that can be put in on replacement or new doors. This type of handle is available in a variety of designs and finishes. A variety of manufacturers provide this handle, including Avocet ERA, Fullex, Hoppe, Mila, Millenco & Yale.
Fab and Fix Windsor Inline Sprung Lever Door Handle
The handles made of uPVC/Composite are made from robust materials, and are ideal for doors with multiple points that require a robust design. The handles are inline and operate off the same spindle and screw fixings so they are easily installed on new or existing uPVC/Composite doors.
The design of the sprung lever allows the handle to be set and angled for comfortable operation and is suitable for all users. The handle has been tested to 200 000 cycles. This helps ensure that the quality of finish and performance over time. The sprung lever can be cut to fit more locks. This is especially useful in doors with smaller door frames where the cylinder is further back. A shorter lever can be used for doors that have a latch that can be opened by the thumb on the inside.
Lever Pad
A Lever Pad door handle made of upvc operates differently than lever handles on doors. These handle types are either operated by a single spindle or by two spindles, either inline or offset. They are generally employed on UPVC double-glazed doors and come in a variety of styles and finishes.
The handles have been tested to a minimum of 200,000 cycles and are available in various finishes, including White, Silver, Chrome & Gold. The finish is BS EN 1670 Grade 5 and is resistant to rust. This gives the handle a high performance and long-lasting durability for its intended use.
All UPVC lever pads for handles come with a spindle, screws and can be mounted on a uPVC door. The backplate fixation centres of 211mm allow for a bigger handle, which is usually an advantage when replacing an old or faulty multi-point door lock mechanism. These handle levers are also sprung, solving the problem of handles hanging from their horizontal position when not in use.
When choosing the replacement UPVC handle and spindle it is essential to match the PZ dimensions of both the multipoint lock and the uPVC door. This measurement may also be called 'handle centres or cylinder centre'. It is important for matching the correct handles.
Once you have decided on the proper PZ size and the correct PZ size, you must ensure that the lever and push pads are designed to fit the American with Disabilities Act compliant handles that you need for your door. They are usually of a round or square shape with an internal lever and external push pad.
Most of the UPVC lever pads we sell are sprung, meaning that they return to their horizontal position after not being used, instead of hanging out and possibly securing in the frame. This stops draughts and cold air from getting into a house. door handles repair near me is also the case that the majority of UPVC handle lever pad style handles are hand-operated, allowing you to install them on either side of the door.
Euro Cylinder
Cylinder locks are typically found on uPVC doors, but they can be utilized on other types of door. The cylinder lock operates by using a key that unlocks the cylinder's case. This exposes pins that can be aligned to the pins in the lock and allow them to rotate the camera that rotates, opening the door. Euro cylinders are available with up to six pins. Internal and external doors require different levels of security.
Choosing the right cylinder is crucial; it is contingent on how your doors and handle are utilized. For instance, doors that are external must be secured with an extra secure cylinder, while doors inside can be secured using an ordinary cylinder. Certain cylinders come with extra features that can improve security, such as anti-drill or anti bump properties.
To make sure that the euro cylinder is the right size for your door, it must be measured accurately. The cylinder needs to be measured from the central screw hole to the ends of the cylinder. This includes the thumb turn, should there be one. It is best to do this while the lock is in place however, when this isn't possible, you may remove it to measure. A cylinder that protrudes beyond the handle and escutcheon could be vulnerable to attacks such as snapping locks, so it is crucial that it is not too long.
Most newer cylinders have been made with bump and anti-drill features included in their design. They are designed to decrease the risk of attack by causing the cylinder to rotate in an opposite direction. This will help deflect the attack, and ensure your door is secure.
There are cylinders designed to withstand snapping. This is a typical attack on cylinders. A specially designed tool is used to break the break line of the lock and the front of the cylinder is snapped off. This is faster and easier to achieve than gaining access through multipoint locks. It also leaves no evidence of a burglary, which could hinder an insurance claim.
Spring Cassette
The spring cassette is situated inside the base plate of your door handle. It offers a spring-loaded solution to bring your multipoint lock handles back to their resting position after usage. Previously a lot of these types of handle did not have a spring integrated into them and without this they are more likely to slide or drop once the locking mechanism is disengaged. This component is the best way to address this issue. It also helps prevent your upvc door from becoming stuck in either the open or closed position as they are difficult to close manually.
These spring cassettes were designed to be used with sprung multipoint locks. They will not fit unsprung handles and you'll need to cut a hole into your backplate for them to fit. (Please check the image for a more detailed diagram). These cassettes are a replacement to damaged or missing cassettes in the backplate of uPVC door handles. They are sold as one unit. They have a square-cut out that can accommodate an 8mm shaft.
These spring cassettes provide a great value solution to the problem of door handles that are sagging. They are simple to install and will extend the lifespan of your uPVC door. Contact us for more information about our selection of uPVC accessories and spares. We are on hand to assist and give you expert advice.